猫盘蓝灯闪，网络只有黄灯闪，ttl启动信息如下，大神帮.....
本帖最后由 mhl1208 于 2021-3-12 01:10 编辑猫盘开机蓝灯闪，网络只有黄灯闪，路由看不到ip ttl启动信息如下，大神帮忙看看怎么救
TIM-1.0
WTMI-armada-17.10.1-
ENTER init_ddrgen
DDR_TOPOLOGY is 0 : DDR3, 1CS 512M
WTMI_CLOCK=2
Fill memory before self refresh...done
Now in Self-refresh Mode
Restore CAS Read and Write Latency
Restore termination values to original values
Exited self-refresh ...
DLL TUNING
==============
DLL 0xc0001050:
DLL 0xc0001050:
DLL 0xc0001054:
DLL 0xc0001054:
DLL 0xc0001074:
DLL 0xc0001074
U-Boot 2017.03-armada-17.10.1 (Nov 30 2017 - 17:27:47 +0800)
Model: Marvell Armada 3720 for Eli Cat
CPU @ 1000
L2 @ 800
TClock @ 200
DDR @ 800
I2C: ready
DRAM:512 MiB
U-Boot DT blob at : 000000001f73a520
SF: Detected GD25LQ64C with page size 256 Bytes, erase size 4 KiB, total 8 MiB
*** Warning - bad CRC, using default environment
MMC: for ssg ledsdhci@d8000: 0
12686 bytes read in 17 ms (728.5 KiB/s)
gpio: pin GPIO23 (gpio 39) value is 1
gpio: pin GPIO23 (gpio 39) value is 1
gpio: pin GPIO23 (gpio 39) value is 1
Comphy-0: UNCONNECTED
Comphy-1: SGMII0 1.25 Gbps
Comphy-2: SATA0 6 Gbps
gpio: pin GPIO23 (gpio 39) value is 1
12686 bytes read in 4 ms (3 MiB/s)
Enter Normal mode
SCSI:Hit any key to stop autoboot:0
gpio: pin GPIO221 (gpio 57) value is 0
gpio: pin GPIO221 (gpio 57) value is 1
gpio: pin GPIO20 (gpio 36) value is 1
12686 bytes read in 3 ms (4 MiB/s)
13006336 bytes read in 292 ms (42.5 MiB/s)
## Flattened Device Tree blob at 01000000
Booting using the fdt blob at 0x1000000
Using Device Tree in place at 0000000001000000, end 000000000100618d
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 4.4.52-armada-17.10.1(sgshi@admin-node) (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05) ) #29 SMP PREEMPT Wed Mar 7 11:32:37 CST 2018
[ 0.000000] Boot CPU: AArch64 Processor
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] cma: Reserved 64 MiB at 0x000000001c000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] PERCPU: Embedded 16 pages/cpu @ffffffc01bfc7000 s25344 r8192 d32000 u65536
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.Total pages: 128512
[ 0.000000] Kernel command line: console=ttyMV0,115200 root=/dev/mmcblk0p1 rootdelay=1 ro
[ 0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.000000] software IO TLB (64MB) mapped at
[ 0.000000] Memory: 360300K/522240K available (8643K kernel code, 541K rwdata, 3076K rodata, 332K init, 311K bss, 96404K reserved, 65536K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB)
[ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)
[ 0.000000] 0xffffffbdc0000000 - 0xffffffbdc0800000 ( 8 MB actual)
[ 0.000000] fixed : 0xffffffbffa7fd000 - 0xffffffbffac00000 (4108 KB)
[ 0.000000] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB)
[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000] memory: 0xffffffc000000000 - 0xffffffc020000000 ( 512 MB)
[ 0.000000] .init : 0xffffffc000bf4000 - 0xffffffc000c47000 ( 332 KB)
[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc000bf3e44 ( 11728 KB)
[ 0.000000] .data : 0xffffffc000c60000 - 0xffffffc000ce7600 ( 542 KB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=2
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] CPU0: found redistributor 0 region 0:0x00000000d1d40000
[ 0.000000] Architected cp15 timer(s) running at 12.50MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
[ 0.000004] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
[ 0.000154] Console: colour dummy device 80x25
[ 0.000175] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=50000)
[ 0.000185] pid_max: default: 32768 minimum: 301
[ 0.000238] Security Framework initialized
[ 0.000275] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.000282] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.000769] Initializing cgroup subsys memory
[ 0.000796] Initializing cgroup subsys hugetlb
[ 0.001032] EFI services will not be available.
[ 0.001052] ASID allocator initialised with 65536 entries
[ 0.036133] Detected VIPT I-cache on CPU1
[ 0.036159] CPU1: found redistributor 1 region 0:0x00000000d1d60000
[ 0.036185] CPU1: Booted secondary processor
[ 0.036237] Brought up 2 CPUs
[ 0.036255] SMP: Total of 2 processors activated.
[ 0.036261] CPU features: detected feature: GIC system register CPU interface
[ 0.036268] CPU: All CPU(s) started at EL2
[ 0.036285] alternatives: patching kernel code
[ 0.036725] devtmpfs: initialized
[ 0.039462] DMI not present or invalid.
[ 0.039784] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.039803] futex hash table entries: 512 (order: 4, 65536 bytes)
[ 0.042069] xor: measuring software checksum speed
[ 0.080182] 8regs :1861.000 MB/sec
[ 0.120211] 8regs_prefetch:1710.000 MB/sec
[ 0.160248] 32regs :2273.000 MB/sec
[ 0.200282] 32regs_prefetch:1984.000 MB/sec
[ 0.200287] xor: using function: 32regs (2273.000 MB/sec)
[ 0.200309] pinctrl core: initialized pinctrl subsystem
[ 0.201357] NET: Registered protocol family 16
[ 0.212438] cpuidle: using governor ladder
[ 0.224355] cpuidle: using governor menu
[ 0.224582] vdso: 2 pages (1 code @ ffffffc000c65000, 1 data @ ffffffc000c64000)
[ 0.224614] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.225336] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.225475] Serial: AMBA PL011 UART driver
[ 0.226764] mvebu-uart d0012000.serial: could not find pctldev for node /soc/internal-regs/pinctrl@13800/uart1-pins, deferring probe
[ 0.336735] raid6: int64x1gen() 373 MB/s
[ 0.404814] raid6: int64x1xor() 380 MB/s
[ 0.472883] raid6: int64x2gen() 597 MB/s
[ 0.540927] raid6: int64x2xor() 513 MB/s
[ 0.609028] raid6: int64x4gen() 911 MB/s
[ 0.677076] raid6: int64x4xor() 644 MB/s
[ 0.745213] raid6: int64x8gen() 946 MB/s
[ 0.813229] raid6: int64x8xor() 614 MB/s
[ 0.881370] raid6: neonx1 gen() 631 MB/s
[ 0.949394] raid6: neonx1 xor() 651 MB/s
[ 1.017494] raid6: neonx2 gen()1034 MB/s
[ 1.085577] raid6: neonx2 xor() 890 MB/s
[ 1.153672] raid6: neonx4 gen()1331 MB/s
[ 1.221737] raid6: neonx4 xor()1014 MB/s
[ 1.289848] raid6: neonx8 gen()1380 MB/s
[ 1.357896] raid6: neonx8 xor()1028 MB/s
[ 1.357901] raid6: using algorithm neonx8 gen() 1380 MB/s
[ 1.357905] raid6: .... xor() 1028 MB/s, rmw enabled
[ 1.357910] raid6: using intx1 recovery algorithm
[ 1.358511] armada3700-avs d0011500.avs: error getting max cpu frequency, try again later
[ 1.358525] armada3700-avs d0011500.avs: armada_3700_avs_probe: failed initialization
[ 1.358958] vgaarb: loaded
[ 1.359244] SCSI subsystem initialized
[ 1.359689] usbcore: registered new interface driver usbfs
[ 1.359751] usbcore: registered new interface driver hub
[ 1.359820] usbcore: registered new device driver usb
[ 1.360285] pxa2xx-i2c d0011000.i2c: could not find pctldev for node /soc/internal-regs/pinctrl@13800/i2c1-pins, deferring probe
[ 1.360417] pps_core: LinuxPPS API ver. 1 registered
[ 1.360423] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 1.360451] PTP clock support registered
[ 1.360801] dmi: Firmware registration failed.
[ 1.361002] armada37xx-clk-pm d0014018.cpu-pm-clk: error getting max cpu frequency, try again later
[ 1.361814] clocksource: Switched to clocksource arch_sys_counter
[ 1.369652] NET: Registered protocol family 2
[ 1.370473] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 1.370522] TCP bind hash table entries: 4096 (order: 4, 65536 bytes)
[ 1.370595] TCP: Hash tables configured (established 4096 bind 4096)
[ 1.370664] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 1.370683] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 1.370839] NET: Registered protocol family 1
[ 1.375261] RPC: Registered named UNIX socket transport module.
[ 1.375275] RPC: Registered udp transport module.
[ 1.375280] RPC: Registered tcp transport module.
[ 1.375284] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.376058] kvm : GICv3: no GICV resource entry
[ 1.376069] kvm : disabling GICv2 emulation
[ 1.376076] kvm : interrupt-controller@ffffffc0000ac668 IRQ12
[ 1.376240] kvm : timer IRQ3
[ 1.376252] kvm : Hyp mode initialized successfully
[ 1.378575] audit: initializing netlink subsys (disabled)
[ 1.378628] audit: type=2000 audit(1.372:1): initialized
[ 1.379227] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.387849] VFS: Disk quotas dquot_6.6.0
[ 1.388024] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.390414] NFS: Registering the id_resolver key type
[ 1.390453] Key type id_resolver registered
[ 1.390458] Key type id_legacy registered
[ 1.390473] Installing knfsd (copyright (C) 1996 [email protected]).
[ 1.391266] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 1.391659] fuse init (API version 7.23)
[ 1.392147] 9p: Installing v9fs 9p2000 file system support
[ 1.394756] async_tx: api initialized (async)
[ 1.394806] io scheduler noop registered
[ 1.395029] io scheduler cfq registered (default)
[ 1.397664] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 1.404333] libphy: Fixed MDIO Bus: probed
[ 1.404352] tun: Universal TUN/TAP device driver, 1.6
[ 1.404356] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 1.405088] libphy: mdio_driver_register: mv88e6xxx
[ 1.405388] libphy: orion_mdio_bus: probed
[ 1.406886] _of_phy_get:index=0
[ 1.406903] lane:1,mode:8192
[ 1.406912] ssg mode:2
[ 1.406917] ssg mode:2,reg:0x0
[ 1.417136] sky2: driver version 1.30
[ 1.417336] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 1.417343] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 1.417404] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.3.0-k
[ 1.417409] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 1.417476] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.0.2-k
[ 1.417482] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 1.417544] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 4.2.1-k
[ 1.417549] ixgbe: Copyright (c) 1999-2015 Intel Corporation.
[ 1.417624] ixgbevf: Intel(R) 10 Gigabit PCI Express Virtual Function Network Driver - version 2.12.1-k
[ 1.417630] ixgbevf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 1.417687] ixgb: Intel(R) PRO/10GbE Network Driver - version 1.0.135-k2-NAPI
[ 1.417692] ixgb: Copyright (c) 1999-2008 Intel Corporation.
[ 1.418634] mv_xor d0060900.xor: Marvell shared XOR driver
[ 1.438394] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq )
[ 1.458399] mv_xor d0060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr pq )
[ 1.463219] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.465307] Unable to detect cache hierarchy from DT for CPU 0
[ 1.470581] brd: module loaded
[ 1.475521] loop: module loaded
[ 1.477575] VFIO - User Level meta-driver version: 0.3
[ 1.478449] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.478468] ehci-pci: EHCI PCI platform driver
[ 1.478532] ehci-platform: EHCI generic platform driver
[ 1.478646] ehci-orion: EHCI orion driver
[ 1.478805] _of_phy_get:index=0
[ 1.488998] _of_phy_get:index=0
[ 1.489022] orion-ehci d005e000.usb: EHCI Host Controller
[ 1.489050] orion-ehci d005e000.usb: new USB bus registered, assigned bus number 1
[ 1.489288] orion-ehci d005e000.usb: irq 9, io mem 0xd005e000
[ 1.497827] orion-ehci d005e000.usb: USB 2.0 started, EHCI 1.00
[ 1.498521] hub 1-0:1.0: USB hub found
[ 1.498556] hub 1-0:1.0: 1 port detected
[ 1.498946] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.498979] ohci-pci: OHCI PCI platform driver
[ 1.499074] ohci-platform: OHCI generic platform driver
[ 1.499479] usbcore: registered new interface driver usblp
[ 1.499533] usbcore: registered new interface driver uas
[ 1.499614] usbcore: registered new interface driver usb-storage
[ 1.500124] i2c /dev entries driver
[ 1.500815] md: linear personality registered for level -1
[ 1.500831] md: raid0 personality registered for level 0
[ 1.500841] md: raid1 personality registered for level 1
[ 1.500850] md: raid10 personality registered for level 10
[ 1.501049] md: raid6 personality registered for level 6
[ 1.501057] md: raid5 personality registered for level 5
[ 1.501062] md: raid4 personality registered for level 4
[ 1.501466] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: [email protected]
[ 1.501850] sdhci: Secure Digital Host Controller Interface driver
[ 1.501858] sdhci: Copyright(c) Pierre Ossman
[ 1.501868] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.502124] xenon-sdhci d00d8000.sdhci: Failed to setup input clk: -517
[ 1.504510] usbcore: registered new interface driver usbhid
[ 1.504523] usbhid: USB HID core driver
[ 1.506462] nf_conntrack version 0.5.0 (3326 buckets, 13304 max)
[ 1.507069] IPv4 over IPsec tunneling driver
[ 1.507749] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.508569] NET: Registered protocol family 10
[ 1.509540] sit: IPv6 over IPv4 tunneling driver
[ 1.510199] NET: Registered protocol family 17
[ 1.510269] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.510357] Bridge firewalling registered
[ 1.510597] 8021q: 802.1Q VLAN Support v1.8
[ 1.510646] 9pnet: Installing 9P2000 support
[ 1.510720] Key type dns_resolver registered
[ 1.510729] mpls_gso: MPLS GSO support
[ 1.511502] registered taskstats version 1
[ 1.518095] Btrfs loaded
[ 1.518555] d0012000.serial: ttyMV0 at MMIO 0xd0012000 (irq = 7, base_baud = 1562500) is a mvebu-uart
[ 1.809823] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 1.945299] usb-storage 1-1:1.0: USB Mass Storage device detected
[ 1.949985] scsi host0: usb-storage 1-1:1.0
[ 2.816568] console enabled
[ 2.821124] i2c i2c-0:PXA I2C adapter
[ 2.825475] _of_phy_get:index=0
[ 2.828302] lane:1,mode:8192
[ 2.831436] ssg mode:2
[ 2.833674] ssg mode:2,reg:0x0
[ 2.847143] ssg phy_mode:3
[ 2.849489] ssg PHY_INTERFACE_MODE_SGMII
[ 2.854658] mvneta d0030000.ethernet eth0: Using device tree mac address 00:51:82:11:22:00
[ 2.927663] _of_phy_get:index=0
[ 2.930581] lane:2,mode:4349
[ 2.933654] ssg mode:1
[ 2.935969] ssg mode:1,reg:0x0
[ 2.939655] ssg mode:1
[ 2.942096] ssg mode:1,reg:0x0
[ 2.946700] ahci-mvebu d00e0000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 2.955209] scsi 0:0:0:0: Direct-Access SanDiskCruzer Blade 1.26 PQ: 0 ANSI: 6
[ 2.957165] sd 0:0:0:0: 7821312 512-byte logical blocks: (4.00 GB/3.73 GiB)
[ 2.958896] sd 0:0:0:0: Write Protect is off
[ 2.959520] sd 0:0:0:0: Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 2.974695]sda: sda1
[ 2.977531] sd 0:0:0:0: Attached SCSI removable disk
[ 2.994676] ahci-mvebu d00e0000.sata: flags: ncq sntf led only pmp fbs pio slum part sxs
[ 3.003681] scsi host1: ahci-mvebu
[ 3.007571] ata1: SATA max UDMA/133 mmio port 0x100 irq 11
[ 3.016784] m25p80 spi32766.0: gd25lq64c (8192 Kbytes)
[ 3.021983] 4 ofpart partitions found on MTD device spi32766.0
[ 3.028182] Creating 4 MTD partitions on "spi32766.0":
[ 3.033428] 0x000000000000-0x0000000c8000 : "Bootloader"
[ 3.039590] 0x0000000c8000-0x0000000cc000 : "Ftd"
[ 3.044937] 0x0000000cc000-0x000000500000 : "Linux"
[ 3.050435] 0x000000500000-0x000000800000 : "Cramfs"
[ 3.056550] armada3700_wdt: Initial timeout 343 sec
[ 3.061868] xenon-sdhci d00d8000.sdhci: No vmmc regulator found
[ 3.067664] xenon-sdhci d00d8000.sdhci: No vqmmc regulator found
[ 3.105830] mmc0: SDHCI controller on d00d8000.sdhci using ADMA
[ 3.116094] hctosys: unable to open rtc device (rtc0)
[ 3.135439] Waiting 1 sec before mounting root device...
[ 3.183462] mmc0: MAN_BKOPS_EN bit is not set
[ 3.195026] mmc0: new HS200 MMC card at address 0001
[ 3.204339] mmcblk0: mmc0:0001 8GME4R 7.28 GiB
[ 3.209185] mmcblk0boot0: mmc0:0001 8GME4R partition 1 4.00 MiB
[ 3.215372] mmcblk0boot1: mmc0:0001 8GME4R partition 2 4.00 MiB
[ 3.221205] mmcblk0rpmb: mmc0:0001 8GME4R partition 3 512 KiB
[ 3.227689]mmcblk0: p1 p2 p3
[ 3.333832] ata1: SATA link down (SStatus 0 SControl 300)
[ 4.145861] md: Waiting for all devices to be available before autodetect
[ 4.152551] md: If you don't use raid, use raid=noautodetect
[ 4.159250] md: Autodetecting RAID arrays.
[ 4.163437] md: Scanned 0 and added 0 devices.
[ 4.168097] md: autorun ...
[ 4.170724] md: ... autorun DONE.
[ 4.175065] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities
[ 4.186417] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[ 4.194684] VFS: Mounted root (ext4 filesystem) readonly on device 179:1.
[ 4.203296] devtmpfs: mounted
[ 4.206499] Freeing unused kernel memory: 332K (ffffffc000bf4000 - ffffffc000c47000)
[ 4.214488] Freeing alternatives memory: 72K (ffffffc000c47000 - ffffffc000c59000)
/sbin/init: error while loading shared libraries: libtirpc.so.3: cannot open shared object file: No such file or directory
[ 4.241908] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00007f00
[ 4.241908]
[ 4.251200] CPU: 1 PID: 1 Comm: init Not tainted 4.4.52-armada-17.10.1 #29
[ 4.258395] Hardware name: Marvell Armada 3720 for Eli-Cat DB-88F3720-DDR3 (DT)
[ 4.265687] Call trace:
[ 4.268489] [<ffffffc000089b10>] dump_backtrace+0x0/0x108
[ 4.274152] [<ffffffc000089c2c>] show_stack+0x14/0x20
[ 4.279293] [<ffffffc000451200>] dump_stack+0x98/0xb8
[ 4.284605] [<ffffffc000147dcc>] panic+0xd4/0x218
[ 4.289205] [<ffffffc0000ba204>] do_exit+0x9b4/0x9b8
[ 4.294156] [<ffffffc0000ba274>] do_group_exit+0x3c/0xa8
[ 4.299825] [<ffffffc0000ba2f0>] __wake_up_parent+0x0/0x28
[ 4.305765] [<ffffffc000085e30>] el0_svc_naked+0x24/0x28
[ 4.310994] CPU0: stopping
[ 4.314051] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.52-armada-17.10.1 #29
[ 4.321521] Hardware name: Marvell Armada 3720 for Eli-Cat DB-88F3720-DDR3 (DT)
[ 4.329166] Call trace:
[ 4.331334] [<ffffffc000089b10>] dump_backtrace+0x0/0x108
[ 4.337267] [<ffffffc000089c2c>] show_stack+0x14/0x20
[ 4.342043] [<ffffffc000451200>] dump_stack+0x98/0xb8
[ 4.347528] [<ffffffc00008efc0>] handle_IPI+0x190/0x1a0
[ 4.353012] [<ffffffc000082598>] gic_handle_irq+0x78/0x168
[ 4.358410] Exception stack(0xffffffc000c63da0 to 0xffffffc000c63ed0)
[ 4.365066] 3da0: ffffffc000c67000 0000008000000000 ffffffc000c63f00 ffffffc000086840
[ 4.373159] 3dc0: 0000000000000145 ffffffc000c44000 0000000000000000 0000000000000000
[ 4.381252] 3de0: 0000000000000001 0000000000000000 00000000000001c0 0100000000000000
[ 4.389256] 3e00: 000d1cef00000000 ffffffc01bfcc040 00000000fffedf25 ffffffc000c63e80
[ 4.397438] 3e20: 0000000000000750 0000000000000000 ffffffc016210060 0000000001ba3e18
[ 4.405801] 3e40: 00000000043c64a9 00000000ffffffff 0000000000000000 00000000d1a88b01
[ 4.413626] 3e60: 0000000000000001 ffffffc000c67000 ffffffc000c67ae8 ffffffc000c40ad8
[ 4.422078] 3e80: ffffffc000c63f20 ffffffc0008f8000 ffffffc000c44000 ffffffc000c67000
[ 4.429911] 3ea0: ffffffc000c60000 0000000000000000 0000000000000000 ffffffc000c63f00
[ 4.438272] 3ec0: ffffffc00008683c ffffffc000c63f00
[ 4.442867] [<ffffffc000085700>] el1_irq+0x80/0xf8
[ 4.447906] [<ffffffc0000edddc>] default_idle_call+0x1c/0x38
[ 4.453839] [<ffffffc0000ee010>] cpu_startup_entry+0x1c8/0x218
[ 4.459957] [<ffffffc0008de010>] rest_init+0x88/0x98
[ 4.465085] [<ffffffc000bf4958>] start_kernel+0x38c/0x3a0
[ 4.470388] [<00000000008e9000>] 0x8e9000
[ 4.474441] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00007f00
[ 4.474441]
人工顶置，帮帮忙吧 又挂了一台，已经不少猫盘完蛋了 发表于 1970-1-1 08:00
都是啥原因挂的，是被封了？ 重新刷解决一切 发表于 1970-1-1 08:00
大神能指导下吗？怎么刷，重置不了，重置就是也是一直蓝灯闪，网络灯绿灯亮 mhl1208 发表于 2021-3-12 11:25
大神能指导下吗？怎么刷，重置不了，重置就是也是一直蓝灯闪，网络灯绿灯亮 ...
TTL刷机，淘宝买根刷机线吧
发表于 1970-1-1 08:00
ttl我有，是刷固件进去吗？就是不知道怎么刷，我感觉是固件有文件丢失了， 再手工顶置，期待大神出现
页:
[1]