星际魔盒可能刷成砖，怎么救
星际魔盒刷机可能成砖了表现出来的开机现象：
1，电源亮灯，主板灯亮，网卡灯亮。
2，蜂鸣器只响一声（刚开机时），风扇转。
3，每5分钟左右，会自动断电重启。
现在怎么救？
谢谢各位！:) 接上TTL线，看输出的什么，在根据情况来刷机。 motohua 发表于 2020-3-18 16:41
接上TTL线，看输出的什么，在根据情况来刷机。
好的。我先试试看。等TTL线来。
谢谢！ TTL后，出来的信息如下，请各位帮帮忙看看，能不能救。谢谢！
U-Boot 2012.07 (Jul 09 2018 - 13:01:30) ver_160517
CPU: Cortex-A7 dual core
MIS_GP1DATO default=0x00000008
MIS_GP1DIR default=0x040000a8
MUXPAD3 default=0x00155049
CRT_MUXPAD1 default=0x00000000
MIS_GP0DATO default=0x00000000
MIS_GP0DIR default=0x00000020
MUXPAD4 default=0x00155249
20170626, setGPIO(45, 1)
20160715, ft5x06_ts reset set to 1(not reset for i2c will crash)
20170626, setGPIO(46, 1)
-- hwinit.c: set gpio39(beep), 41,43(i2c2), gpio40,42(fan_low/hi), gpio47(reset USB HUB) --
reg=0x00000000 0
reg=0x00ee0008 0-1
Board: Realtek QA Board
DRAM:1 GiB
Watchdog: Disabled
Cache: Enabled
Non-Cache Region: 1 MB@0x07900000
MMC: rtk_emmc : Detect chip rev. >= B
RTD1195 eMMC: 0
rtk_emmc : Detect chip rev. >= B
mmc->version=0x00010000
version=0x00000004
SDR select (sample/push) : 0x00/0x00
cardtype=57, mmc->card_caps=0f
TBD : to support DDR50/HS200
SDR bus width=2
SDR select (sample/push) : 0x00/0x00
mmc->boot_caps = 203
sdr50 : 0
exit from mmc_startup(),err=0
Device: RTD1195 eMMC
Manufacturer ID: 15
OEM: 100
Name: 4FPD3
Tran Speed: 31975000000000a
Rd Block Len: 512
MMC version 4.0
High Capacity: No
Capacity: 3.6 GiB
Bus Width: 8-bit
Speed: SDR50
Factory: MMC
Factory: pp:1, seq#:0x1c, size:0x20e00
------------can't find tmp/factory/000BootParam.h
------------can't find tmp/factory/video_rpc.bin
tv_system=25 mode=1
----------VOUT_CONFIG_TV_SYSTEM----------
interfaceType =0x0
videoInfo.standard=0x19000000
videoInfo.enProg =0x1
videoInfo.enDIF =0x1
videoInfo.enCompRGB =0x0
videoInfo.pedType =0x1000000
videoInfo.dataInt0=0x4000000
videoInfo.dataInt1=0x0
hdmiInfo.hdmiMode =0x1000000
hdmiInfo.audioSampleFreq =0x3000000
hdmiInfo.audioChannelCount=0x1
hdmiInfo.dataByte1 =0x0
hdmiInfo.dataByte2 =0x0
hdmiInfo.dataByte3 =0x0
hdmiInfo.dataByte4 =0x0
hdmiInfo.dataByte5 =0x0
hdmiInfo.dataInt0 =0x1000000
-----------------------------------------
In: serial
Out: serial
Err: serial
LVDS: on
Net: Realtek PCIe GBE Family Controller mcfg = 0024
dev->name=r8168#0
Hit Esc or Tab key to enter console mode or rescue linux:0 20170626: MUXPAD3=0x00155049, MIS_GP1DIR=0x0400e5a8, MIS_GP1DATO=0x0000e508
------------can't find tmp/factory/recovery
Press Esc Key
Enter console mode, disable watchdog ...(boot_mode=0)
Realtek> 现在变成这样了。开机风扇不转，蜂鸣器也不叫。
U-Boot 2012.07 (Jan 27 2016 - 17:16:49)
CPU: Cortex-A7 dual core
Board: Realtek Demo Board
DRAM:1 GiB
Watchdog: Disabled
Cache: Enabled
Non-Cache Region: 1 MB@0x07900000
MMC: rtk_emmc : Detect chip rev. >= B
RTD1195 eMMC: 0
rtk_emmc : Detect chip rev. >= B
mmc->version=0x00010000
version=0x00000004
SDR select (sample/push) : 0x00/0x00
cardtype=57, mmc->card_caps=0f
TBD : to support DDR50/HS200
SDR bus width=2
SDR select (sample/push) : 0x00/0x00
mmc->boot_caps = 203
sdr50 : 0
exit from mmc_startup(),err=0
Device: RTD1195 eMMC
Manufacturer ID: 15
OEM: 100
Name: 4FPD3
Tran Speed: 31975000000000a
Rd Block Len: 512
MMC version 4.0
High Capacity: No
Capacity: 3.6 GiB
Bus Width: 8-bit
Speed: SDR50
Factory: MMC
Factory: pp:1, seq#:0x130, size:0x21600
get_bootparam:
------------can't find tmp/factory/000BootParam.h
Factory RO: MMC
No factory_ro data in eMMC
In: serial
Out: serial
Err: serial
Net: Realtek PCIe GBE Family Controller mcfg = 0024
dev->name=r8168#0
Hit Esc or Tab key to enter console mode or rescue linux:0
------------can't find tmp/factory/recovery
Press Esc Key
Enter console mode, disable watchdog ...
Realtek> uboot还在，不怕，继续刷 不是用ttl刷机的？ 还没有变砖，接TTL放心刷 应该是刷进4.3.4固件了，只进过一次系统（NAS00000509），断电之后永远进不了。LOG如下
U-Boot 2012.07 (Jan 27 2016 - 17:16:49)
CPU: Cortex-A7 dual core
Board: Realtek Demo Board
DRAM:1 GiB
Watchdog: Disabled
Cache: Enabled
Non-Cache Region: 1 MB@0x07900000
MMC: rtk_emmc : Detect chip rev. >= B
RTD1195 eMMC: 0
rtk_emmc : Detect chip rev. >= B
mmc->version=0x00010000
version=0x00000004
SDR select (sample/push) : 0x00/0x00
cardtype=57, mmc->card_caps=0f
TBD : to support DDR50/HS200
SDR bus width=2
SDR select (sample/push) : 0x00/0x00
mmc->boot_caps = 203
sdr50 : 0
exit from mmc_startup(),err=0
Device: RTD1195 eMMC
Manufacturer ID: 15
OEM: 100
Name: 4FPD3
Tran Speed: 31975000000000a
Rd Block Len: 512
MMC version 4.0
High Capacity: No
Capacity: 3.6 GiB
Bus Width: 8-bit
Speed: SDR50
Factory: MMC
Factory: pp:1, seq#:0x130, size:0x21600
get_bootparam:
------------can't find tmp/factory/000BootParam.h
Factory RO: MMC
No factory_ro data in eMMC
In: serial
Out: serial
Err: serial
Net: Realtek PCIe GBE Family Controller mcfg = 0024
dev->name=r8168#0
Hit Esc or Tab key to enter console mode or rescue linux:0
------------can't find tmp/factory/recovery
======== Checking into android recovery ====
Start Boot Setup ...
fw desc table base: 0x00620000, count: 6
Normal boot fw follow...
Kernel:
FW Image to 0x03000000, size=0x0058bbd0, 0x2c5e blocks (0x0358bbd0)
FW Image fr 0x008b7600, fr block 0x45bb (non-lzma)
DT:
FW Image to 0x01ff2000, size=0x000064fa, 0x33 blocks (0x01ff84fa)
FW Image fr 0x00630000, fr block 0x3180 (non-lzma)
resolution = <0x500 0x2d0>
ROOTFS:
FW Image to 0x02200000, size=0x00400000, 0x2000 blocks (0x02600000)
FW Image fr 0x01a43200, fr block 0xd219 (non-lzma)
Audio FW:
FW Image to 0x01b00000, size=0x0027f528, 0x13fb blocks (0x01d7f528)
FW Image fr 0x00638000, fr block 0x31c0 (non-lzma)
Start A/V Firmware ...
L# Booting kernel from
HegDMacIyIRmaagweaEt n03a0b00l00e0 : ...M
OG I mACage3DNTamSe :M PELGin2ux -A3.A1C0. D2D0-Pa Wl-M2A.5P.3R
e M LImPag
T
ypSeP: DIAF RMR aLiwn uxE Knearnbell eIm:ag eM (PGun coAmpCr3es sDTedS)
MPE GDa2t a ASiAzCe:DDPW58M15A1P84R BOyt esM =L P5 .5
M
iBF
DTrceLo a2d cAdhd reFsso:r 0m01a0t80:00
S EDntTrSy HPoDi ntA: C 030 10D80D00P
m MLVePri fAAyCin gW CMAhPecRkOsu
..
@@@@@@@One Step TV System magic number = 0xc0941540, addr = 0xb8071100@@@@@@@
@@@@@@No hdmi mode
HDMIOff = 1
st 25 p 1 1 0
ped 1 data00x00000004 data10x00000000
st 25 p 1 1 0
ped 1 data00x00000004 data10x00000000
inten.i 0 hdmi 0
(TVE) TVE_DAC_mode 0,,cmd->enProg 1!! ~~comp 1, ch2 0, mode_3D 0!!
~~TVE standard#
OK
## Flattened Device Tree blob at 01ff2000
Booting using the fdt blob at 0x01ff2000
Loading Kernel Image ... OK
OK
Starting kernel ...
SetVideoStandard return!
(VO_ConfigHDMI_InfoFrame) L:232, is_hdmi_plugin 0, hdmiMode 2!!Mode 2 dataByte10x000000000x000000df0x00000001
dataByte40x000000000x00000000 int00x81d853c4
Mode 2 dataByte10x000000000x000000df0x00000001
dataByte40x000000000x00000000 int00x81d853c4
fw turn off 0xb800d044 =0x00000000!
boot_info0xa0000000 magic0x92526300 en 76
check 0x 0x180056e4, HDMI Mode?(0)
[ 1.100538] venus_i2c_bus_jam_recover1416 end
[ 1.110203] venus_i2c_bus_jam_recover1416 end
[ 1.120200] venus_i2c_bus_jam_recover1416 end
[ 1.160488] venus_i2c_bus_jam_recover1416 end
[ 1.170201] venus_i2c_bus_jam_recover1416 end
[ 1.180199] venus_i2c_bus_jam_recover1416 end
[ 1.717531] get reg-ir-dpir = 50ld us from dtb, regval=0x2500lx
Set Debug level0x00000001
-------------------
Audio Version = 890778 (phoenix)
Common Version = 0
Binary src compiled at Dec 14 2015 10:26:11
Note =
-------------------
gloabl malloc size0x003ffeb8
[ 1.792202] AudioIntrRead:141 can't find process for handling AudioIntrRead programID:98
[ 1.801231] AudioIntrRead: program:98 version:0 procedure:1 taskID:0 sysTID:4294967295 sysPID:4294967295 size:4 context:81d8d5d5 atomic
[ 2.026154] dwc3 18020000.dwc3: no usb2 phy configured
[ 3.420902] venus_i2c_bus_jam_recover1416 end
[ 3.920381] venus_i2c_bus_jam_recover1416 end
[ 4.419882] venus_i2c_bus_jam_recover1416 end
[ 4.919381] venus_i2c_bus_jam_recover1416 end
[ 6.777537] venus_i2c_bus_jam_recover1416 end
[ 7.277022] venus_i2c_bus_jam_recover1416 end
[ 7.776521] venus_i2c_bus_jam_recover1416 end
[ 8.276022] venus_i2c_bus_jam_recover1416 end
[ 8.835379] rtc-rx8010 3-0032: Unable to write register #23
[ 8.841085] i2c i2c-3: probing for rx8010 failed
[ 8.851683] cpufreq: Failed to obtain VDDARM: -517
[ 8.856615] cpufreq: Only frequency scaling available
[ 9.058999] cpufreq: Failed to obtain VDDARM: -517
[ 9.063900] cpufreq: Only frequency scaling available
[ 9.125129] ilitek_init,996,ilitek.dev.remove_flag =0
[ 9.474695] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
resize2fs 1.42.9 (28-Dec-2013)
The filesystem is already 89598 blocks long.Nothing to do!
resize2fs 1.42.9 (28-Dec-2013)
The filesystem is already 20472 blocks long.Nothing to do!
[ 9.644539] hub 3-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
[ 9.764386] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 9.871606] hub 4-0:1.0: port 1, status 0203, change 0000, 5.0 Gb/s
[ 9.994363] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
initramfs_qnap.cpio.gz: OK
md5sum check OK!
unzip initramfs_qnap.cpio.gz Success!
49442 blocks
extract initramfs_qnap.cpio Success!
Untar /mnt/emmcp5/mnt/boot_disk/boot/rootfs2.tgz success
rootfs_tas.tgz: OK
rootfs_tas.tgz - md5sum check OK!
Untar rootfs_tas.tgz success
resize2fs 1.42.13 (17-May-2015)
The filesystem is already 15352 (1k) blocks long.Nothing to do!
页:
[1]