|
|
启动显示如下，卡在Starting kernel ...不动，大家帮我看看是什么原因0 f6 h0 m5 \* v7 Q! z+ Q
: m5 O7 t/ j& ]2 ]: tTIM-1.0
5 }9 a0 f( e$ s0 `% YWTMI-armada-17.10.1- \. \/ G7 \5 [
ENTER init_ddrgen
+ n! A! V, y. E" c1 \" p- H3 e* kDDR_TOPOLOGY is 0 : DDR3, 1CS 512M
* J1 p6 ^ S* b8 b: a" e7 `WTMI_CLOCK=2
' o9 |+ G& ^8 [8 o6 p: c$ F- a6 M2 a/ @; y
Fill memory before self refresh...done
! ~" E$ X' F# O3 t8 e3 z* Y; b' R7 b) O& L8 D W6 W# E o
Now in Self-refresh Mode0 x1 _: h/ S0 u% y. `" Y" ~
Restore CAS Read and Write Latency7 v3 f4 p. V& r$ U
Restore termination values to original values
: Q# P& o' X5 z& X( }% T7 x3 r3 vExited self-refresh ...6 Y* c9 f+ I L3 n
) u5 l# `" x+ V
DLL TUNING. `2 t% l2 c9 i8 [5 j; ~
==============
/ b6 N2 H! ^/ G$ g/ l DLL 0xc0001050[21:16]: [0,33,19]
4 m) p4 S: Q w; n! b: H( D. P DLL 0xc0001050[29:24]: [4,33,1b]5 @6 A J0 F7 Y, z
DLL 0xc0001054[21:16]: [0,30,18]
& P3 ]; e# R5 d5 `/ V" V3 G1 n DLL 0xc0001054[29:24]: [4,34,1c]# O6 Y( u# V+ ~
DLL 0xc0001074[21:16]: [0,3f,1f]2 t9 ?& i1 h% p x2 W5 y c5 Q
DLL 0xc0001074$ M7 e( d0 \, V# }; |+ _
6 Y4 c( _2 h6 N) U' R# V! R. B/ _U-Boot 2017.03-armada-17.10.1 (Nov 30 2017 - 17:27:47 +0800)) ~0 ]. R& R3 u4 h$ W
) o& q/ }5 B* Z9 m gModel: Marvell Armada 3720 for Eli Cat
( b/ j7 k G9 m* @% U CPU @ 1000 [MHz]
- x, P5 V, ~& F* K" ^$ g L2 @ 800 [MHz]9 P# d/ C6 [: i; i
TClock @ 200 [MHz]8 n! ?; U6 K" R3 f& M: v
DDR @ 800 [MHz]
1 ^* T9 n% q) O1 wI2C: ready 0 `" P) m" V4 J
DRAM: 512 MiB
! R) l/ W5 T' t. L7 c) CU-Boot DT blob at : 000000001f73a520; v0 ^5 E' I/ h8 J
SF: Detected GD25LQ64C with page size 256 Bytes, erase size 4 KiB, total 8 MiB- r u a0 J1 q6 Q, M
MMC: for ssg ledsdhci@d8000: 07 ?( e7 s9 \6 c
** File not found boot/armada-3720-customer0.dtb **( s$ b8 I8 j) [ Q& `
test_mmc_ext4_exist ==10 T0 ~( ?% o' r C: C5 U3 y1 L
Comphy-0: UNCONNECTED ' z" H& n6 s; U/ p
Comphy-1: UNCONNECTED
8 e% n( j. G9 x6 d/ |# _0 QComphy-2: UNCONNECTED
& m9 g, i+ u3 ^" ~gpio: pin GPIO23 (gpio 39) value is 1/ G8 | I; [% ?7 V
** File not found boot/armada-3720-customer0.dtb **
^% S; K3 b" V% K& V* Y5 [7 EEnter Recovery mode6 N' ?; v; u4 C# g: T6 p
SCSI: Hit any key to stop autoboot: 0 9 c; t( u# a/ F' Q" q+ v! [
SF: Detected GD25LQ64C with page size 256 Bytes, erase size 4 KiB, total 8 MiB {5 C( W# Q; ?: j* ~
device 0 offset 0xcc000, size 0x434000$ A2 j% \9 s6 I0 s4 |5 U
SF: 4407296 bytes @ 0xcc000 Read: OK1 G/ H+ n/ n K+ c' w' P4 V; s
gpio: pin GPIO21 (gpio 37) value is 1
) M. I9 s# D& hgpio: pin GPIO22 (gpio 38) value is 13 K: y$ `+ S2 h# M( y
Error: inflate() returned -37 @; C5 h( s1 n! |
device 0 offset 0xc8000, size 0x4000
- G8 t# A6 k+ _7 T) _9 }7 oSF: 16384 bytes @ 0xc8000 Read: OK
/ l+ U! M! L% y## Flattened Device Tree blob at 04f000005 {* |5 v+ X2 E7 t# n4 N) h% M
Booting using the fdt blob at 0x4f00000/ N, }9 I$ b0 ]
Using Device Tree in place at 0000000004f00000, end 0000000004f05caa
+ `, B7 d* }! k# l
/ J! o5 |& @+ L- |Starting kernel ...
6 Q$ `$ g& C9 [- A8 k: |
( d' c5 d; B) E& ~1 \ }. ?
. ~7 [" N# z! M# L h% y9 o |
|
|Archiver|手机版|小黑屋|矿渣社区
( 黔ICP备2024020525号-1 )
发表于 2019-10-2 18:08:56
